Got 4 new tires. They had a red dot and a yellow dot marked on the tire wall. Tire shop guy mounted 3 tires on the wheels such that more or less the red dot was aligned with the tire valve. On those tires, the yellow dot was quite close to the red dot. So perhaps it could be the yellow dot that was aligned with the tire valve. But as I see it, the red dot was closer. On the 4th tire, the angle of separation between the red dot and the yellow dot was a bit less than 180 deg. Tire shop guy aligned the yellow dot with the tire valve. I asked why not the red dot and the guy said it should be yellow dot. Subsequently all wheels were balanced. Also all tire valves (whole valve - stem and all - rubber type) were replaced too.
Afterwards on googling info on red dots and yellow dots, what I gathered from a few sites was that when mounting the tire, the yellow dot should be aligned with the tire valve but if a red dot is present, that should be aligned with the tire valve.
(1) Is this correct? Then the tire shop guy was wrong and knew only part of the method.
(2) Now that the 4th tire is "balanced", does it matter whether the valve stem was aligned to the yellow dot and not the red dot ? I did not test out at highway speeds yet, but did not feel any significant vibration upto say about 70 kmph. But am no expert. If this matters, I will need to get the tire re-mounted and balanced before the dots get fully wiped off.
(3) Is it recommended to change the whole tire value when replacing with a new tire? I ask because, afterwards, I heard some bad stories of cheap tire valves failing.. So wondered if the tire valves that came with the car from japan, even though old (say 10 years or more) would have been better than new cheap tire valves available in tire shops. I can not turn back time, but for other vehicles I can be more cautious.
I woke up one day and I now want to buy a W140. The brain works in mysterious ways. It definitely doesn't understand the concept of money since I am nowhere near affording one.
The first Rolls Royce Spectre goes to drum roll please...... Ukraine! And a Minister as well. Supposedly $600,000/-, reminds me of another country where the story is the same where people suffer and the politicians enjoy themselves.
So these unregistered 2017ish cars rotting in car sales, better than a used or worse?
Need shitbox car asap. Budget is 6.5mil
utter reliable no nonsense car needed. Nice to drive is welcome. Something new ish.
few alto and every vans in my budget, should I? Tires and rubber bits scare me.
Question
eyepea
Got 4 new tires. They had a red dot and a yellow dot marked on the tire wall. Tire shop guy mounted 3 tires on the wheels such that more or less the red dot was aligned with the tire valve. On those tires, the yellow dot was quite close to the red dot. So perhaps it could be the yellow dot that was aligned with the tire valve. But as I see it, the red dot was closer. On the 4th tire, the angle of separation between the red dot and the yellow dot was a bit less than 180 deg. Tire shop guy aligned the yellow dot with the tire valve. I asked why not the red dot and the guy said it should be yellow dot. Subsequently all wheels were balanced. Also all tire valves (whole valve - stem and all - rubber type) were replaced too.
Afterwards on googling info on red dots and yellow dots, what I gathered from a few sites was that when mounting the tire, the yellow dot should be aligned with the tire valve but if a red dot is present, that should be aligned with the tire valve.
(1) Is this correct? Then the tire shop guy was wrong and knew only part of the method.
(2) Now that the 4th tire is "balanced", does it matter whether the valve stem was aligned to the yellow dot and not the red dot ? I did not test out at highway speeds yet, but did not feel any significant vibration upto say about 70 kmph. But am no expert. If this matters, I will need to get the tire re-mounted and balanced before the dots get fully wiped off.
(3) Is it recommended to change the whole tire value when replacing with a new tire? I ask because, afterwards, I heard some bad stories of cheap tire valves failing.. So wondered if the tire valves that came with the car from japan, even though old (say 10 years or more) would have been better than new cheap tire valves available in tire shops. I can not turn back time, but for other vehicles I can be more cautious.
Thanks
Link to comment
Share on other sites
2 answers to this question
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.