Jump to content

Search the Community

Showing results for tags 'panel'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • AUTOLANKA
    • General Automotive
    • News & Updates
    • Feedback & Suggestions
    • DIY (Do-It-Yourself)
    • User Manuals & Service Manuals
    • BLOGS
  • ASK AN EXPERT
    • Mechanical problems
    • Electrical problems
    • General
    • Car Buying Information
  • MOTORING EVENTS
    • Local Events
    • International Events
  • OTHER
    • PC and other Console Games
    • The Lounge
  • SPECIFIC MAKES
    • HONDA SRI LANKA
    • SUBARU
    • MITSUBISHI
    • NISSAN
    • TOYOTA
    • MAZDA
    • BMW
    • MERCEDES BENZ
    • MINI (CLASSIC & NEW)
    • PERODUA
    • PEUGEOT
    • OTHERS
  • OUTDOOR 4X4
    • General
    • Events
    • Trips
  • LEGAL
    • Ask for Advice
    • Share Advice
    • General

Calendars

  • AutoLanka Calendar
  • Southern Motor Sports Club's Events

Blogs

There are no results to display.

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Location


Interests


Vehicle Make


Vehicle Model


Engine Type


Mechanical Mods


Cosmetic Mods


Future Plans


General Comments

Found 3 results

  1. Ok so this is my first ever DIY post so bear with me. Recently I happened to buy a e46 it was in good nic till…. well the cluster died on me . I was looking at dishing out some 140K for a virgin cluster with programming or having to buy a used one and live with wrong mileage and the DREADED tamper dot. Being a software guy by trade, I started looking into buying a used one and to somehow reprograming it to get the correct mileage and VIN. It went well, thus this DIY. My existing cluster was Motormeter and my replacement was Bosch. Doesn’t really matter the manufacturer any e46 cluster should work but I got a pre-facelift cluster cause I’m paranoid. This DIY assumes you have NCSExpert installed and updated with the latest DATEN files. You are going to need a bucket load of stuff. A used e46 cluster (ebay) T20, T10 torx bit drivers. (ebay) Pieces of paper Some experience in hot air soldering (I’m a complete noob at it) A good hot air soldering station Solder Paste/Solder wic Tweezers Surgical Alcohol / Probably some beer too Cotton Wool Nerves of steel Blank M35080 EEPROM chip (ebay) R270+ chip programmer (ebay) A steady hand K+DCAN USB to OBDII cable (ebay) - http://www.ebay.com/itm/BMW-USB-OBD-DIAGNOSTIC-CABLE-INTERFACE-INPA-K-DCAN-ISTA-ISID-SSS-V32-Progman-/331800219469?hash=item4d40d58f4d:g:RpsAAOSw~otWcZo8&item=331800219469&vxp=mtr NCS Expert with latest E46 SP-DATEN files (I had v54 downloaded from https://mega.co.nz/#F!0N8A3LSb!kPyNeBaKoO1GaGoSokfuJA) Cluster Removal Pretty straight forward. Use the T20 torx bit and unfasten the 2 screws at the top. Unlock and pull steering wheel towards you and down to make room to take the cluster out. Pull the cluster out straight and try to partially take it out to the right hand side. There are two connectors at the back. One for power and the other is the CANBUS connector. You want to rotate the white tabs up so the connector backs out of the socket and pull them off. New Cluster Install Install the new cluster temporarily. Reverse of the way it was removed. Check if everything works properly. It doesn’t matter if you get a cog like sign on the panel where the gear selection is display. It will go away once you code it later. Plug in your OBD cable and fire up NCS Expert. Turn key to the 2nd position. No need to start the vehicle. Mine is a 2001 Preface-Lift so it might be different in newer cars. Load the Expert Mode profile. Press “Vin/ZCS/FA” ZCS/FA f. ECU E46 KMB (KMB means instrument cluster) You want to make note / take a screenshot of the FG code. This is the VIN that’s stored in the replacement cluster. Turn off the ignition. And remove the cluster and take it to your work area. Cluster Dis-assembly You might want to practice with the dead cluster first. I did and it was worth the experience. Mark where the 4 T10 screws are located. There are many more holes than screws for some reason. Better to put them back where they were removed from. Unscrew the all of them and pull off the back cover. Holding the circuit board from the square socket connectors pull it straight out. You would want to take care not to touch the black printed board with all the speed / rpm values and stuff. It’s a matte black paint and gets scratched easily (ask me how I know), which will ruin the cluster. Tap the 5 needles so they are settled at the lowest position. Take some pics of exactly where they stop/rest because you are gonna remove them and you want to put them back at the correct positions. Now take a clean piece of paper, rip it in the middle like the pic and place it between the needle and printed board. This is for protection because you are bound to scratch the board if you do not. Now twist the needles counter clockwise while pulling up very gently. It’ll take about two full turns before the needles come out. If you pull too much the black pieces at the middle tend to brake off (This is why you should practice on the dead cluster). You want to remove the RPM needle last because it gets blocked by the fuel consumption needle when you try to turn it. At assembly the fuel consumption needle should be installed last. Once all the needles are removed, gently pull out the printed card and then the clear plastic bit under it. Next remove the two LCD panels (if automatic) one if manual, by releasing the clips at the back and pushing the metal frames out. Take note of the orientation they come out at. You would want to put them back the same way. Now the white plastic back panel should come off easily.
  2. Hi all, For all who might find the below helpful. Cheers! Instrument cluster translation from Japanese to English: Download - user manual: http://www.suzuki.co.jp/car/owners_manual/files/2_99011-52R02_20170906035005.pdf
  3. nish1

    Open Door Panel

    Hi guys, Bad yesterday I faced to a bad incident, Its Like this I have sicked a sun shade on my drivers door shutter and mistakenly I pushed the auto shutter down button, how bad was it the sun shade stucked in side the door, fortunately when I pushed back it up, it just came out but one single plastic sun shade holder(you know what I mean the plastic thing used to stick the sun shade to the shutter ) stucked in side the shutter and the door panel. So now the panel not seated well to the door and when the shutter turning up and down it giving creepy sound also...(because of rubbing the two phases) Can somebody tel me a good/clean work/no harming to my door panel/not making scratches/ place me to get that thing out from inside my door? I guess somebody who working in power shutters will do this in perfect manner.. It's about my VITZ Thanks pals..
×